Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
Which of the following describes the Port Address Translation configuration? A. Manually configured, one-to-one address mapping B. Automatically assigned from an address pool, many-to-many address mapping C. Many-to-one address mapping https://www.learncisco.net/courses/icnd-1/acls-and-nat/address-translation.html Which command is used to import a static default route into the RIP routing process and have it advertised to other neighboring RIP routers? A. default-information originate B. redistribute static C. ip route 0.0.0.0 0.0.0.0 next-hop_ip D. network 0.0.0.0 What is the name of the Cisco product that offers a number of rack-mountable server configurations intended to be used in data centers? A. ASA B. KVM C. CRC D. UCS Which statements describe a trunk operation? (Choose two) A. It carries traffic for a single virtual LAN, or VLAN B. It's the link between an Ethernet switch interface and a router C. Cisco supports the 802.1 Q trunking protocol D. It excludes traffic from the native VLAN https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/trunk-operations.html Which options are not one of the manageable QoS characteristics of network traffic? (Choose two) A. Delay B. Jitter C. Queue size D. Clock rate E. Bandwidth F. Loss Which of the following route types is used when one of the router`s interfaces is attached to the network? A. Directly connected B. Default route C. Dynamic routing D. Static routing https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/static-routing.html You have implemented DAI on a Layer 2 switch in your network. Now you want to monitor the ARP message rates with an average of four received ARP messages a second. Which command(s) would need to be utilized to accomplish this? (Choose two) A. ip arp inspection limit rate 8 burst interval 2 B. ip arp inspection limit rate 4 burst interval 2 C. ip arp inspection limit rate 10 burst interval 5 D. ip arp inspection limit rate 20 burst interval 5 What are three benefits of implementing VLANs? (Choose three) A. A higher level of network security can be reached by separating sensitive data traffic from other network traffic. B. A more efficient use of bandwidth can be achieved allowing many physical groups to use the same network infrastructure. C. A more efficient use of bandwidth can be achieved allowing many logical networks to use the same network infrastructure. D. Broadcast storms can be mitigated by increasing the number of broadcast domains, thus reducing their size. E. Broadcast storms can be mitigated by decreasing the number of broadcast domains, thus increasing their size. F. VLANs make it easier for IT staff to configure new logical groups, because the VLANs all belong to the same broadcast domain. G. Port-based VLANs increase switch-port use efficiency, thanks to 802.1Q trunks. https://www.learncisco.net/courses/ccna/part-5-virtual-lans-vlans/vlans-review.html What can VLANs be used for? (Choose two) A. To maximize device resources B. To segment a physical switch into logical broadcast domains C. To prevent specific protocols from entering your network D. To eliminate the need for routers Which CLI prompt indicates the correct way to set the port duplex operation to full? A. switchX>duples full B. switchX(config-if)#duplex half C. switchX(config-if)#duplex full D. switchX(config)#full duplex https://www.learncisco.net/courses/icnd-1/ethernet-lans/starting-a-switch.html Which of the following is required when configuring port security with sticky learning? A. Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand B. Enabling port security with the switchport port-security interface subcommand C. Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand D. All the other answers list required commands Which layer of the OSI model establishes, manages, and terminates sessions between two communicating hosts? A. Session B. Network C. Transport D. Application E. Data-link F. Presentation https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html R1, R2, R3, and R4 have their Fast Ethernet 0/0 interfaces attached to the same VLAN. A network engineer has typed a configuration for each router by using a word processor. He will later copy and paste the configuration into the routers. Examine the following exhibit, which lists configuration for the four routers, as typed by the network engineer. Assuming that all four routers can ping each other’s LAN IP addresses after the configuration has been applied, choose the routers that will be able to form a neighbor relationship with the other routers on the LAN. (You can assume that, if not shown in the exhibit, all other related parameters are still set to their defaults.) (Choose two) A. R1 B. R2 C. R3 D. R4 E. None of the routers will exchange routing information. Which IPv6 command allows you to verify general parameters such as the reference bandwidth? A. show ipv6 ospf interface brief B. show ipv6 ospf C. show ipv6 route summarization D. show ipv6 protocols You want to verify the Cisco IOS software version, ROM version, amount of memory, type of processor, number and types of interfaces, as well as the configuration register value on your 2900 series IOS router. What command will allow you to accomplish this? A. Show startup-configuration B. Show running-configuration C. Show version D. Show flash What are some perceived benefits of controller-based networks as compared to traditional networks? (Choose two) A. New operational models that allow for a single device to be instantiated with the entire network in mind B. The use of APIs to mass-configure network devices, allowing for more consistency and fewer errors C. The use of DevOps approaches in the network to increase efficiency and productivity D. The use of legacy approaches in the network to increase efficiency and productivity What command should you configure globally to enable a 15-minute recovery time for the port security errdisable state? A. errdisable recovery interval 15 B. errdisable recovery timer 15 C. errdisable recovery timer 900 D. errdisable recovery interval 900 Which command can be used to find the default gateway address on a Windows PC? A. show ipv6 route B. ping C. netsh D. ipconfig If a lightweight AP provides at least one BSS for wireless clients, which one of the following modes does it use? A. Local B. Normal C. Monitor D. Client Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two) A. The transport layer divides a data stream into segments and may add reliability and flow control information. B. The data link layer adds physical source and destination addresses and an FCS to the segment. C. Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information. D. Packets are created when the network layer adds Layer 3 addresses and control information to a segment. E. The presentation layer translates bits into voltages for transmission across the physical link. https://www.learncisco.net/courses/ccna/part-1-internetworking/data-encapsulation.html When comparing controller-based networks and traditional networks what are some perceived benefits from a controller-based perspective? (Choose two) A. New operational models that allow the entire network to be instantiated and not just a single device at a time B. The use of automation through APIs that enable data-driven models C. New operational models that allow for a single device to be instantiated with the entire network in mind D. The use of legacy approaches in the network to increase efficiency and productivity Per the command output, with how many routers is router R9 full adjacent over its Gi0/0 interface? A. 7 B. 10 C. 5 D. 2 Which QoS feature is typically used inbound to a network to limit the amount of traffic that is allowed to flow in? A. Traffic classification B. Traffic shaping C. Traffic limiting D. Traffic policing What are the steps to configure a static route? (Choose two) A. Use the Media Access Control, or MAC, address of the next hop router B. Configure unidirectional static routes to and from a stub network C. Use the inbound interface of the local routers D. Define a path to the IP destination network https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/static-routing.html Which Cisco IOS command is used to advertise a default route into an OSPF domain regardless of whether a default static route is configured? A. default-information originate B. default-information originate always C. default-information originate permanent D. default-information originate no-check You are performing password recovery on your 2900 ISR. You have successfully merged the startup configuration file, changed all the passwords, and enabled all the required interfaces. What else do you need to do in order to complete the password recovery process successfully? (Choose two) A. Copy the contents of NVRAM to RAM B. Copy the running configuration to the startup configuration C. Change the configuration register value D. Issue the boot system command E. Reload the router Which of the following attributes do QoS tools manage? (Choose three) A. Bandwidth B. Delay C. Load D. MTU E. Loss What protocols exist to negotiate EtherChannel creation and maintenance? (Choose two) A. LACP B. VTP C. PAgP D. STP What are the considerations when using IPv6 global unicast addresses? (Choose two) A. It starts with 2000::/3 and is assigned by IANA B. Home sites typically require multiple subnets C. Subnetting is more efficient and has less waste than with IPv4 D. A shorter prefix length allows more available address space During a maintenance window, you make some changes to R2. You document these changes in your configuration management system. Later that night, you are called in to fix an issue that requires you to make additional changes to R2. The next morning your co-worker addresses another issue but this time on R1. All of these changes are documented properly but neither you or nor your coworker discuss the changes. These changes stay implemented for months. What is this best described as? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Which of the following commands globally enables PortFast on all nontrunking ports? A. spanning-tree portfast default B. spanning-tree portfast C. spanning-tree bpduguard enable D. spanning-tree portfast bpduguard default https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/performance-with-spanning-tree.html You have just upgraded your Cisco IOS image on your Cisco 2900 ISR from 12.4 to the following image: C2900-universalk9-mz.SPA-152-4.M1.bin You have also deleted the 12.4 IOS image from the ISR. However, when you issue the “show version“ command, you notice that the 12.4 operating system is still in use. How do you solve this issue? A. Issue the command copy tftp flash B. Issue the boot system command C. Reboot the router D. Copy the running configuration to the startup configuration E. Issue the command copy flash tftp The Wi-Fi Alliance offers which of the following certifications for wireless devices that correctly implement security standards? A. WEP B. WPA2 C. 802.11 D. AES Which of these are QoS requirements when designing a Cisco TelePresence video network? (Choose two) A. One-way delay < 200 ms B. Round-trip delay < 200 ms C. Loss < 5% D. Loss < 0.05% E. Jitter < 100 ms F. Jitter < 50 ms In a split-MAC architecture, real-time functions such as encryption are handled in which of the following network entities? A. An access layer switch B. A distribution layer switch C. A wireless LAN controller D. A lightweight AP Which of the following cloud services is most likely to be purchased and then used to later install your own software applications? A. IaaS B. PaaS C. SaaS D. SLBaaS Which of the following components holds the diagnostic software that is used when the router powers up? A. Interface B. ROM C. Flash D. RAM E. CPU F. NVRAM https://www.learncisco.net/courses/icnd-2/network-management/router-internal-components-overview.html You are configuring dynamic NAT on your Cisco IOS router. Which command is used to verify the interfaces that are being used as the outside interface and the inside interface? A. show interfaces B. show ip route C. show ip nat translations D. show ip interface brief E. show ip interface F. show ip nat statistics What is the multicast address for hello packets by default on OSPFv3? A. 224.0.0.6 B. FF02::A C. FF02::5 D. 224.0.0.5 Which of the following describes dynamic routing protocols? (Choose two) A. They are configured on Layer 2 switches B. They can choose an alternate path to a learned network when the current path no longer exists C. They are best used in small networks D. They are statically configured with remote networks E. They can choose the best path to a learned network when multiple paths exist Which of the following four TCP/IP layers represents the core of the TCP/IP architecture? A. Network Access B. Transport C. Internet D. Application https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html Which of the following describes a static NAT configuration? A. Manually configured, one-to-one address mapping B. Automatically assigned from an address pool, many-to-many address mapping C. Many-to-one address mapping https://www.learncisco.net/courses/icnd-1/acls-and-nat/address-translation.html What is required for a directly connected route to be added to the routing table? (Choose two) A. The network command must be issued under the routing process B. BGP must be running on the router C. A local route must be manually created D. The IP route command must be configured in global configuration mode E. Configure an IP address on the interface F. The interface Status must be up and the Protocol must be up What is the name of the protocol that has been developed by the ONF that is used to communicate between an SDN controller and the network devices it controls? A. OpFlex B. OpenSDN C. SbControl D. OpenFlow enable secret [password] is hashed using the _______ algorithm. A. MD5 B. AH C. PSK D. ESP E. WPA2 Which Cisco IOS router prompt indicates that you are in Global Configuration mode? A. Router# B. Router(config-if)# C. Router. D. Router> E. Router(config)# Refer to the diagram. What is the name of the device referenced with the arrow, assuming the traffic coming from the wireless clients followed the dashed path? A. Autonomous AP B. Lightweight AP C. Wireless controller D. Wireless router Which cloud service model provides access to an application that is built, monitored, and offered by the cloud provider? A. TaaS B. IaaS C. PaaS D. SaaS Host A and Host B sit in two different subnets. The path between the subnets of these two hosts runs through three different Layer 3 forwarding devices (routers and Layer 3 switches). A network engineer uses the APIC-EM Path Trace ACL Analysis tool to analyze the path used for Host A to send packets to Host B. Which part of the function is done specifically by the ACL Analysis or ACL Trace part of the tool? A. Discovery of the topology that exists between the two hosts B. Analysis of the Layer 3 forwarding decisions in the path from Host A to B C. Analysis of the Layer 2 forwarding decisions in the path from Host A to B D. Analysis of the impact of ACLs on the packets that would flow from Host A to B Which switch ”show” command is used to display the IP address, subnet mask and default gateway settings? A. show version B. show interfaces C. show running-config https://www.learncisco.net/courses/icnd-1/ethernet-lans/starting-a-switch.html R3 has a static route configured that points toward the service provider. What command could you use to have R3 advertise an OSPFv3 default route to the internal network, regardless of whether R3 had its default static route? A. The decision to advertise a default route depends on the static route always being present on R3. B. The default behavior is to redistribute any default IPv6 routes into OSPFv3, so no action is required. C. Each of the other routers needs a static default route that leads to R3. D. Use the command default-information originate always in interface mode for G1/0 on R3. E. Have R3 use the command default-information originate always in OSPFv3 router configuration mode. Which is the Hello and Dead interval with a Gigabit Ethernet connection for a BROADCAST Network type with IPv6 by default? A. Hello 60, Dead 120 B. Hello 10, Dead 40 C. Hello 40, Dead 10 D. Hello 20, Dead 120 You are implementing a VLSM network. You are using the Class B network of 172.16.0.0/16 and need to create 256 networks from this. The fifth network will then be subnetted into /30 networks. What is the subnet ID of the fourth /30 network? A. 172.16.4.12/30 B. 172.16.4.4/30 C. 172.16.4.6/30 D. 172.16.4.8/30 E. 172.16.4.14/30 F. 172.16.4.10/30 In a reflection attack, the source IP address in the attack packets is spoofed so that it contains which one of the following entities? A. The address of the attacker B. The address of the reflector C. The address of the victim D. The address of the router You are configuring RIP on your Cisco IOS router. Which configuration command will successfully enable RIPv2? A. R1(config)#router rip R1(config-router)#2 B. R1(config)#router rip version 2 C. R1(config)#router rip R1(config-router)#version 2 D. R1(config)#router rip 1 R1(config-router)#version 2 E. R1(config)#router rip 2

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources