Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
If you want to be alerted when a device configuration differs from the intended configuration, what should you implement? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Four OSPF routers connect to the same LAN. In a new election after all routers have been rebooted, which router wins the DR election? A. R4, router-id 4.4.4.4, priority 1 B. R3, router-id 3.3.3.3, priority 2 C. R1, router-id 1.1.1.1, priority 4 D. R2, router-id 2.2.2.2, priority 3 Of the figures shown, which depicts an accurate Clos Architecture? A. Topology A B. Topology B C. Topology C D. Topology D In a split-MAC architecture, real-time functions such as encryption are handled in which of the following network entities? A. An access layer switch B. A distribution layer switch C. A wireless LAN controller D. A lightweight AP Output from the “show interface“ command indicates that input queue drops are occurring. What does this signify? A. Errors have been identified during the transmission of a frame B. There is congestion on the outgoing interface C. More traffic is arriving on the interface than the router can process D. Errors have been identified during the reception of a frame Refer to the exhibit. Why has this switch not been elected the root bridge for VLAN1? A. It has more than one interface that is connected to the root network segment. B. It is running RSTP while the elected root bridge is running 802.1d spanning tree. C. It has a higher MAC address than the elected root bridge. D. It has a higher bridge ID than the elected root bridge. Which statements are true about telnet and ssh? (Choose two) A. Only data traffic is encrypted with ssh B. All telnet traffic is sent in plain text C. All ssh traffic is encrypted D. The data is hashed by telnet during transmission E. The username and password is hashed by telnet during authentication F. Only authentication traffic is encrypted with ssh Which QoS feature is typically used inbound to a network to limit the amount of traffic that is allowed to flow in? A. Traffic classification B. Traffic shaping C. Traffic limiting D. Traffic policing Which cloud service model provides access to an application that is built, monitored, and offered by the cloud provider? A. TaaS B. IaaS C. PaaS D. SaaS Which of the following options are provided by private VPNs? (Choose two) A. Security B. Cost C. No control of resources D. Enterprise Access is less secure Which command would you use to enter the OSPF routing configuration mode? A. Router(config-router)#network 10.0.0.0 0.0.0.255 0 B. Router(config)#router ospf 1 C. Router(config)#network 10.0.0.0 0.0.0.255 area 0 D. Router(config)#router ospf https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/single-area-ospf.html A network uses an SDN architecture with switches and a centralized controller. Which of the following terms describes a function or functions expected to be found on the switches but not on the controller? A. A Northbound Interface B. A Southbound Interface C. Data plane functions D. Control plane functions Which layer in the hierarchical Cisco Enterprise Campus Architecture is used to provide end users with connectivity to the network? A. Aggregation B. Edge C. Distribution D. Access E. Core Which command would you use to specify a VLAN's ID on a switch? A. vlan 20 B. configure vlan 20 C. name 20 D. vlan sales From the following options, what are the required REST API attributes? (Choose two) A. JSON-formatted data B. Unlayered systems C. Layered systems D. Client-server architecture Refer to the diagram. What is the official name of the network (Network A) that is broadcast by an AP? A. SSID B. BSS C. ESS D. SRDID Per the command output, with how many routers is router R9 full adjacent over its Gi0/0 interface? A. 7 B. 10 C. 5 D. 2 Which of the following OSPF packet types sends missing information to the neighbors? A. link-state acknowledgement, or LSAck B. link-state update, or LSU C. link-state request, or LSR D. database description package, or DBD https://www.learncisco.net/courses/icnd-2/an-overview-of-ospf/link-state-databases.html It is typical for server processors to utilize a technique that allows each physical processing core to be split into a number of virtual cores; this is commonly referred to as __________. A. processor virtualization B. multi-threading C. virtual processing D. processor switching Think about a policing function that is currently working, and also think about a shaping function that is also currently working. That is, the current bit rate of traffic exceeds the respective policing and shaping rates. Which statements are true about these features? (Choose two) A. The policer may or may not be discarding packets. B. The policer is definitely discarding packets. C. The shaper may or may not be queuing packets to slow down the sending rate. D. The shaper is definitely queuing packets to slow down the sending rate. What commands would you need to configure to enable DHCP Snooping so that PC4 couldn’t become a rogue DHCP server? A. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/12, ip dhcp snooping trust B. Configure the following on SW 1: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/24, ip dhcp snooping trust C. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/24, ip dhcp snooping trust D. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/24, ip dhcp snooping trust E. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/12, ip dhcp snooping trust F. Configure the following on SW 1: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/24, ip dhcp snooping trust Which layer of the OSI model establishes, manages, and terminates sessions between two communicating hosts? A. Session B. Network C. Transport D. Application E. Data-link F. Presentation https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html Which statements provide reasons as to why you would implement a DHCP server in your Enterprise environment? (Choose two) A. It will automatically assign MAC addresses to clients in accordance to VLAN settings B. It is a favourable solution when mobile clients exist in the network C. It provides host-based security including anti-virus and anti-malware D. It will discover the MAC address to IPv4 address mappings for clients E. It will automatically assign IPv4 addresses to clients in accordance to VLAN settings What source will be chosen when a destination network offers multiple sources? A. The dynamic route B. The route with the highest metric C. The source with the lowest administrative distance D. The static route https://www.learncisco.net/courses/icnd-1/lan-connections/functions-of-routing.html A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of the protocol stack that the network administrator is using for this operation? A. application B. presentation C. session D. transport E. internet F. data link https://www.learncisco.net/courses/ccna/part-1-internetworking/the-osi-reference-model.html What are the characteristics of a VLAN? (Choose two) A. It allows you to segment users by function as long as they are in the same LAN segment B. It offers segmentation of broadcast domains C. It replaces the use of broadcast domains in your network D. It allows you to logically segment a network What is the metric referred to as for RIPv2? A. Cost B. Hop-count C. Metric D. AS-path E. Feasible distance A Cisco Catalyst switch connects to what should be individual user PCs. Each port has the same port security configuration, configured as follows: interface range gigabitethernet 0/1 - 24 switchport mode access switchport port-security switchport port-security mac-address sticky Which of the following answers describe the result of the port security configuration created with these commands? (Choose two) A. Prevents unknown devices with unknown MAC addresses from sending data through the switch ports. B. If a user connects a switch to the cable, prevents multiple devices from sending data through the port. C. Will allow any one device to connect to each port, and will save that device’s MAC address into the startup-config D. Will allow any one device to connect to each port, but will not save that device’s MAC address into the startup-config What will the solicited node multicast address be for the IPv6 address 2001:DB8:1001:F:2C0:10FF:FE17:FC0F? A. FF02:0000:0000:0000:0000:10FF:FE17:FC0F B. FF02:0000:0000:0000:0000:0001:FF17:FC0F C. 2001:0000:0000:0000:0000:0001:FF17:FC0F D. FF02:0000:0000:0000:0000:0001:FE17:FC0F Which of the following is required when configuring port security with sticky learning? A. Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand B. Enabling port security with the switchport port-security interface subcommand C. Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand D. All the other answers list required commands When comparing next-generation IPS to traditional IPS, what additional capabilities can be leveraged to more efficiently block traffic? (Choose three) A. AVC B. Signature-based filtering C. Contextual awareness D. Event impact level If a lightweight AP provides at least one BSS for wireless clients, which one of the following modes does it use? A. Local B. Normal C. Monitor D. Client What occurs when there are no more port numbers for PAT to use during translation? A. Packets are forwarded as is B. A port number will be chosen from the range 512 to 1023 C. A port number will be chosen from the range 1024 to 65535 D. Packets are dropped E. Packets are buffered until there are available port numbers F. A port number will be chosen from the range 0 to 511 Refer to the diagram. What method of authentication is being used? A. Open authentication B. CCMP C. WEP D. 802.1x Which command is used to import a static default route into the RIP routing process and have it advertised to other neighboring RIP routers? A. default-information originate B. redistribute static C. ip route 0.0.0.0 0.0.0.0 next-hop_ip D. network 0.0.0.0 You can use output filters in combination with any show command. Which of the following displays the full area of output that starts with the filtering expression? A. include B. exclude C. begin D. section https://www.learncisco.net/courses/icnd-1/lan-connections/starting-a-router.html You need to create 8 subnets in the 192.168.1.0/24 network. What is the new network mask that will be used and how many hosts can be used on each of the subnets? (Choose two) A. 30 hosts B. 126 hosts C. Network mask /27 D. Network mask /25 E. Network mask /26 F. 62 hosts https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html Refer to the graphic. Host A is communicating with the server. What will be the source MAC address of the frames received by Host A from the server? A. the MAC address of router interface e0 B. the MAC address of router interface e1 C. the MAC address of the server network interface D. the MAC address of host A What is the name of the Cisco feature that allows for the identification of protocols that are traditionally hard to classify because of their operation? A. DSCP B. NBAR C. DTerm D. CBWFQ Review the topology diagram. Network 10.123.0.0/24 is the backbone area. Network 10.12.0.0/24 is area 1, and network 10.34.0.0/29 is in area 2. Which of the following are true? (Choose three) A. R1 is a backbone router. B. R1 is an ABR. C. R1 is an internal router. D. R3 would see the OSPF network of 10.12.0.0/24 as an intra-area route. E. R1 and R3 would have the same LSA information about the backbone area. Which of the following route types is used when the route is populated by routing information exchanges? A. Directly connected B. Default route C. Dynamic routing D. Static routing https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/dynamic-routing.html You are upgrading your Cisco IOS image on your 2900 ISR. You won't be removing the old IOS image from the device for disaster recovery reasons. After copying the IOS image from the tftp server to flash and rebooting the device, you notice that the old operating system image is still loading. How can you load the new IOS image? A. Issue the boot system command and reload the device B. Issue the config-register 0x2142 command and reload the device C. Issue the copy running-config startup-config command D. Issue the write memory command What command will successfully change the configuration register so that a Cisco IOS 2900 series router will boot into ROM Monitor mode? A. Config-register 0x2104 B. Config-register 0x2105 C. Config-register 0x2101 D. Config-register 0x2102 E. Config-register 0x2120 F. Config-register 0x2103 G. Config-register 0x2106 In what security zone are the public web servers located? A. DMZ B. Inside C. Outside D. Campus What is the final determining method of breaking a tie during the STP operation? A. Lower cost B. Lower priority C. Lower upstream BID D. Lower port ID Which of the following route types is used when the route is manually configured by a system administrator? A. Directly connected B. Default route C. Dynamic routing D. Static routing https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/static-routing.html You are given an IP address of 172.16.3.0/23. What is the usable range of addresses within this subnet? A. 172.16.0.0 to 172.16.4.254 B. 172.16.1.0 to 172.16.3.254 C. 172.16.3.1 to 172.16.4.254 D. 172.16.2.1 to 172.16.3.254 https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html An enterprise plans to start using a public cloud service, and is considering different WAN options. The answers list four options under consideration. Which options provide good security by keeping the data private while also providing good QoS services? (Choose two) A. Using private WAN connections directly to the cloud provider B. Using an Internet connection without VPN C. Using an intercloud exchange D. Using an Internet connection with VPN Which options are not one of the manageable QoS characteristics of network traffic? (Choose two) A. Delay B. Jitter C. Queue size D. Clock rate E. Bandwidth F. Loss R3 has a static route configured that points toward the service provider. What command could you use to have R3 advertise an OSPFv3 default route to the internal network, regardless of whether R3 had its default static route? A. The decision to advertise a default route depends on the static route always being present on R3. B. The default behavior is to redistribute any default IPv6 routes into OSPFv3, so no action is required. C. Each of the other routers needs a static default route that leads to R3. D. Use the command default-information originate always in interface mode for G1/0 on R3. E. Have R3 use the command default-information originate always in OSPFv3 router configuration mode. Which two link protocols are used to carry multiple VLANs over a single link? (Choose two) A. VTP B. 802.1q C. IGP D. ISL E. 802.3u https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html Refer to the exhibit. All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two) A. Network A - 172.16.3.48/26 B. Network A - 172.16.3.128/25 C. Network A - 172.16.3.192/26 D. Link A - 172.16.3.0/30 E. Link A - 172.16.3.40/30 F. Link A - 172.16.3.112/30 Looking at the exhibit, what key:value pair option has a value that is numeric in nature? A. ”upTime”: ”45 days, 13:36:14.80”, B. ”lastUpdated”: ”2019-10-29 02:52:00”, C. ”managementIpAddress”: ”10.230.1.1”, D. ”lastUpdateTime”: 1572317520439 Which statements best describe physical and logical topologies? (Choose two) A. The physical topology requires that data takes the shortest path across the network towards its destination B. The physical topology is dependent on the type of cabling that is used C. The logical topology can allow data to take a longer path across the network towards its destination D. The primary categories of logical topologies are bus, star, and mesh https://www.learncisco.net/courses/icnd-1/building-a-network/the-functions-of-networking.html You are implementing a VLSM network. You are using the Class B network of 172.16.0.0/16 and need to create 256 networks from this. The fifth network will then be subnetted into /30 networks. What is the subnet ID of the fourth /30 network? A. 172.16.4.12/30 B. 172.16.4.4/30 C. 172.16.4.6/30 D. 172.16.4.8/30 E. 172.16.4.14/30 F. 172.16.4.10/30

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources