Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
Which of the following use cases are matching the Fiber Ethernet media type? (Choose two) A. Offers the highest bandwidths compared to the other forms of communication B. A four-pair wire with low cost and low signal degradation C. Acts as a wave guide to transmit light between the two ends https://www.learncisco.net/courses/icnd-1/building-a-network/connecting-to-a-lan.html What is the Administrative Distance of internal EIGRP routes? B. 170 C. 90 D. 20 E. 1 F. 110 G. 120 Some IOS commands store passwords as clear text, but you can then encrypt the passwords with the service password-encryption global command. By comparison, other commands store a computed hash of the password, rather than storing the password. Comparing the two options, which one answer is the most accurate about why one method is better than the other? A. Using hashes is preferred because encrypted IOS passwords can be easily decrypted. B. Using hashes is preferred because of the large CPU effort required for encryption. C. Using encryption is preferred because it provides stronger password protection. D. Using encryption is preferred because of the large CPU effort required for hashes. Which of the following describes dynamic routing protocols? (Choose two) A. They are configured on Layer 2 switches B. They can choose an alternate path to a learned network when the current path no longer exists C. They are best used in small networks D. They are statically configured with remote networks E. They can choose the best path to a learned network when multiple paths exist A _________ is a virtual instance of a traditional networking device that a consumer can use in a cloud. A. virtual network function B. virtual network appliance C. network virtualized element D. network cloud device In Software-Defined Access (SDA), which of the answers are part of the overlay data plane? A. LISP B. GRE C. OSPF D. VXLAN What type of variable is being shown? Routers = [R1,R2,R3] A. List B. Dictionary C. Simple D. Unsigned integers A switch’s port Gi0/1 has been correctly enabled with port security. The configuration sets the violation mode to restrict. A frame that violates the port security policy enters the interface, followed by a frame that does not. Which of the following answers correctly describe what happens in this scenario? (Choose two) A. The switch puts the interface into an err-disabled state when the first frame arrives. B. The switch generates syslog messages about the violating traffic for the first frame. C. The switch increments the violation counter for Gi0/1 by 1. D. The switch discards both the first and second frame. Which of the following are available methods of classifying packets in DiffServ on Cisco routers? (Choose three) A. Matching the IP DSCP field B. Matching the 802.1p CoS field C. Matching fields with an extended IP ACL D. Matching the SNMP Location variable Which statements accurately describe a network? (Choose three) A. A network is a collection of connected devices that have the ability to communicate with each other B. Networks are capable of transmitting data in many kinds of environments, such as homes, small businesses, and large enterprises C. A main office can have hundreds or even thousands of people who depend on network access to do their jobs D. A main office usually has one large network to connect users E. Remote locations cannot connect to a main office through a network F. The purpose of a network is to allow workers access to all information and components that are accessible by the network https://www.learncisco.net/courses/icnd-1/building-a-network/the-functions-of-networking.html Which hash method is used by default when using the enable secret Cisco IOS command? A. 3DES B. MD5 C. SHA-0 D. HMAC Four OSPF routers connect to the same LAN. In a new election after all routers have been rebooted, which router wins the DR election? A. R4, router-id 4.4.4.4, priority 1 B. R3, router-id 3.3.3.3, priority 2 C. R1, router-id 1.1.1.1, priority 4 D. R2, router-id 2.2.2.2, priority 3 Regarding lightweight AP modes, which one of the following is true? A. An AP can operate in multiple modes at the same time. B. An AP only has one possible mode of operation. C. The Run mode is the default mode. D. The SE-Connect mode is used for spectrum analysis. Which option can you choose for saving money while securing your WAN connections? A. Enterprise Managed VPN B. Service Provider VPN C. SSL VPN D. Access Control VPN Which command enables IPv6 forwarding on a Cisco router? A. ipv6 local B. ipv6 host C. ipv6 unicast-routing D. ipv6 neighbor https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-connectivity.html What can be verified in the output of show interfaces trunk? (Choose five) A. The VLANs allowed on the trunk B. The encapsulation method used for the trunk C. The access vlan the port is a member of if it is not a trunk D. The interfaces are trunks E. The Native VLAN for the trunk F. The administrative mode used to form the trunk G. If DTP is enabled or disabled From the following options, what are the required REST API attributes? (Choose two) A. JSON-formatted data B. Unlayered systems C. Layered systems D. Client-server architecture Connections can be verified using a variety of troubleshooting commands. Which of the following commands is used to display incoming and outgoing connections? A. netstat B. tracert C. ping D. nslookup https://www.learncisco.net/courses/icnd-1/lan-connections/packet-delivery-process-at-l3.html Review the topology. All subnets exist in OSPF area 0. Which command, if issued on R3, would show all the LSAs known by R3? A. Show running-config B. Show ip ospf interface C. Show ip ospf neighbors D. Show ip route ospf E. Show ip ospf database How is Telnet used to verify connectivity? (Choose two) A. It shows you the path required to reach the end device B. To determine if you have access to a particular service on a device C. It uses ICMP Echo requests to test connectivity D. To verify basic connectivity to a device What is the default mode of STP running on a Cisco Catalyst switch? A. PVST+ B. STP C. Rapid PVST+ D. MSTP E. RSTP Refer to the exhibit. All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem? A. The access link needs to be configured in multiple VLANs. B. The link between the switches is configured in the wrong VLAN. C. The link between the switches needs to be configured as a trunk. D. VTP is not configured to carry VLAN information between the switches. E. Switch IP addresses must be configured in order for traffic to be forwarded between the switches. Which of the following describes the PVST+ protocol? A. Assumes one 802.1D spanning tree for the entire bridged network B. Provides a separate 802.1D spanning tree for each virtual LAN, or VLAN, configured C. Provides fast conversion with a single instance of STP D. Provides fast conversion with an instance of spanning tree per VLAN https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/stp-protocol-types.html You are using CDP to build a network topology. Which command is used to verify the IPv4 address of the neighboring Cisco IOS device? A. show interfaces B. show cdp C. show ip interfaces D. show cdp neighbors E. show cdp neighbors detail F. show ip interface brief You are configuring HSRP for VLAN 10. You want its primary default gateway to be R1 and secondary default gateway be R2. What should you consider when configuring HSRP for R1? (Choose two) A. Ensure that you use the same group number for all your configuration commands B. Ensure that pre-emption is disabled C. To ensure R1 always has priority, use the IP address of the physical interface of R1 for the virtual IP address D. Ensure that you specify R2 has a lower priority than R1 Which features make IPv6 an improvement over IPv4 addressing? (Choose two) A. Uses Time to Live, or TTL, values in the header B. Security and mobility build into the standard C. Larger address space D. Offers approximately 4.3 billion addresses https://www.learncisco.net/courses/icnd-1/introducing-ipv6/the-ipv6-address.html In a split-MAC architecture, real-time functions such as encryption are handled in which of the following network entities? A. An access layer switch B. A distribution layer switch C. A wireless LAN controller D. A lightweight AP Per the command output, with how many routers is router R9 full adjacent over its Gi0/0 interface? A. 7 B. 10 C. 5 D. 2 enable secret [password] is hashed using the _______ algorithm. A. MD5 B. AH C. PSK D. ESP E. WPA2 During a maintenance window, you make some changes to R2. You document these changes in your configuration management system. Later that night, you are called in to fix an issue that requires you to make additional changes to R2. The next morning your co-worker addresses another issue but this time on R1. All of these changes are documented properly but neither you or nor your coworker discuss the changes. These changes stay implemented for months. What is this best described as? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Which of the following devices is used by the service provider to provide WAN services? A. Router B. Core router C. WAN switch D. CSU/DSU https://www.learncisco.net/courses/icnd-2/wan-technologies/wan-connections-overview.html Which priority value should you set for a switch to give it the best chance of remaining as a root bridge in the long term? A. 32768 B. 4096 C. 61440 D. 0 (zero) R1, R2, R3, and R4 have their Fast Ethernet 0/0 interfaces attached to the same VLAN. A network engineer has typed a configuration for each router by using a word processor. He will later copy and paste the configuration into the routers. Examine the following exhibit, which lists configuration for the four routers, as typed by the network engineer. Assuming that all four routers can ping each other’s LAN IP addresses after the configuration has been applied, choose the routers that will be able to form a neighbor relationship with the other routers on the LAN. (You can assume that, if not shown in the exhibit, all other related parameters are still set to their defaults.) (Choose two) A. R1 B. R2 C. R3 D. R4 E. None of the routers will exchange routing information. Which DSCP marking group was created to be backward compatible with Internet Protocol Precedence (IPP) values? A. EF B. AF C. CS D. PF What is the name of the Cisco feature that allows for the identification of protocols that are traditionally hard to classify because of their operation? A. DSCP B. NBAR C. DTerm D. CBWFQ What does PAT use to keep each translation unique? A. A protocol number B. A combination of a port number and protocol number C. An IP address D. A port number E. A combination of an IP address and a port number F. A combination of an IP address and a protocol number What should be checked when troubleshooting IPv6 end-to-end connectivity? (Choose three) A. Incorrect default gateways B. Physical location of devices C. Physical connection issues D. Blocked traffic from ACLs Which cloud service model gives a customer complete control over the virtual hardware components, including processor performance, network connectivity, how much memory and storage space is required, and potentially the operating system that is preinstalled? A. SaaS B. IaaS C. PaaS D. TaaS Which statement about VLAN operation on Cisco Catalyst switches is true? A. When a packet is received from an 802.1Q trunk, the VLAN ID can be determined from the source MAC address and the MAC address table. B. Unknown unicast frames are retransmitted only to the ports that belong to the same VLAN. C. Broadcast and multicast frames are retransmitted to ports that are configured on different VLAN. D. Ports between switches should be configured in access mode so that VLANs can span across the ports. https://www.learncisco.net/courses/icnd-1/ethernet-lans/developing-design-for-layer-2.html You are configuring RIPv2 on your Cisco IOS router. Which command and configuration mode is used to enable the RIP routing process on an interface? A. R1(config-router)#interface interface_id B. R1(config-if)#ip rip enable C. R1(config-router)#network network_id D. R1(config-if)#network network_id Which of the following are required attributes of a REST-based API? (Choose two) A. Uses HTTP B. Objects noted as to whether they can be cached C. Classful operation D. Client/server architecture Refer to the diagram. What method of authentication is being used? A. Open authentication B. CCMP C. WEP D. 802.1x An enterprise plans to start using a public cloud service and is considering different WAN options. The answers list four options under consideration. Which one option has the most issues if the company chooses one cloud provider but then later wants to change to use a different cloud provider instead? A. Using private WAN connections directly to the cloud provider B. Using an Internet connection without VPN C. Using an intercloud exchange D. Using an Internet connection with VPN Which of the following is required when configuring port security with sticky learning? A. Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand B. Enabling port security with the switchport port-security interface subcommand C. Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand D. All the other answers list required commands What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology? A. path cost B. lowest port MAC address C. VTP revision number D. highest port priority number E. port priority number and MAC address https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/spanning-tree-operations.html Which of the commands will successfully create a named ACL called WEB_ACCESS that you can add permit and deny entries to for controlling access to web resources? A. access-list standard WEB_ACCESS B. ip access-list extended WEB_ACCESS C. ip access-list standard WEB_ACCESS D. access-list extended WEB_ACCESS Your router has learned about the network 172.17.8.0/24 from EIGRP and OSPF. What information will the router populate the routing table with? A. Both the EIGRP and OSPF information; and load balancing will occur B. The OSPF information because it has the lower administrative distance C. The EIGRP information because it has the lower administrative distance D. The EIGRP information because it has the lower metric E. The OSPF information because it has the lower metric What is used to determine the MAC address of a known IPv6 address? A. ARPv6 B. DHCP C. ARP D. DHCPv6 E. Router discovery F. Neighbor discovery Refer to the exhibit. Based on the information given, which switch will be elected root bridge and why? A. Switch A, because it has the lowest MAC address B. Switch A, because it is the most centrally located switch C. Switch B, because it has the highest MAC address D. Switch C, because it is the most centrally located switch E. Switch C, because it has the lowest priority F. Switch D, because it has the highest priority Which of the following attributes do QoS tools manage? (Choose three) A. Bandwidth B. Delay C. Load D. MTU E. Loss Please choose the correct sequence of the following data encapsulation steps: 1. The layer 3 header is added to the data before being passed on the next layer. 2. A header is added to previous data and is passed to the Internet layer. 3. A trailer, usually the frame check sequence of FCS, and a header are added. 4. An application sends user data. A. 4, 3, 2, 1 B. 1, 2, 3, 4 C. 4, 2, 1, 3 D. 3, 4, 2, 1 What versions of Wi-Fi Protected Access (WPA) were defined after the IEEE ratified the IEEE 802.11i security standard? (Choose two) A. WPA B. WPA2 C. WPA3 D. WPA0 You are configuring PAT on your Cisco IOS router. Which command is used to identify the private IP addresses that can be translated? A. access-list 1 permit 10.1.1.0 0.0.0.63 B. ip nat outside C. ip nat pool NAT_POOL 203.0.113.3 203.0.113.6 prefix-length 29 D. ip nat inside E. ip nat inside source list 1 interface fastethernet0/0 overload You are configuring dynamic NAT on your Cisco IOS router. Which command is used to verify the interfaces that are being used as the outside interface and the inside interface? A. show interfaces B. show ip route C. show ip nat translations D. show ip interface brief E. show ip interface F. show ip nat statistics How do you modify the reference bandwidth with OSPFv3? A. Auto-cost bandwidth B. Auto-cost reference bandwidth C. Change ipv6 bandwidth D. IPv6 ospf reference bandwidth

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources